1.     Charging your headset
2.     Charging & LED Status matrix
3.     Connecting your headset to the charger
4.     Multi- function controller
5.     Resetting the headset
6.     General operation


1. Charging Your Headset

The headset comes with a built-in rechargeable Lithium-Polymer battery that will provide you with approximately 4 hours of the talk time or 110 hours of standby time.

• Be sure to charge the headset for a minimum of 4 hours before using the unit for the first time.
• Be sure to use only the charging adapter supplied with you headset or the optional STEP USB charging adapter. The use of   other adapters may damage your unit and will void the warranty
• While charging our headset for the first time, the LED indicator will glow a constant red
• Other information provided by the LED indicator is described in the following chart.

2. Charging & LED Status Matrix

Your STEP 1150 will be fully recharged after approximately 4 hours of charging, and approximately 80% of a full charge after only 2 hours of charging. The table below explains the various modes of the LED indicator during charging.

Your charger is also supplied with a charger adapter cable approximately 23 cm (9 inches) long. This adapter cable is used to connect your headset to your charger to the optional charging devices available from STEP. WARNING: do not attempt to charge you step 1150 with charging adapters from other companies. Doing so may damage your step 1150 and void your warranty.

To charge you headset, connect the adapter cable to the charger if it is not already connected, and then plug the adapter cable to the headset as shown.

- Note: the charging adapter is ‘keyed’ to fit only one way into your headset. Do not force the adapter cable into the connecting port of the headset as this may damage your headset and void your warranty.
Paring the headset

4. Multi- Function Controller

Before you start using the headset for the first time, you must pair the headset with the mobile phone or device want to use it with.

1. Being by activating the Bluetooth TM paring function on your phone or other device. Please refer to the owner’s     manual of  your phone or other device for detailed instructions on how to access and activate the Bluetooth     paring or set-up procedure.

2. With the headset turned off, press and hold down the multi-function control for approx 5 seconds until the LED     indicator light on the headset flashes an alternating green and red. Make sure the headset and the phone are     in close proximity to each other.

3. Follow the Bluetooth TM paring or set-up instructions and screen prompts on your phone or other device to pair     it  with the headset.

4. When prompted, enter the headset passkey of 0000.

5. If the paring is successful, your headset indicator light will flash green.

If your phone or device does not find the headset, turn off the headset by pressing down the multi-function control for approximately 5 seconds, reset your phone or device to the beginning of the Bluetooth paring process, and repeat steps 1-5. once paring is completed, your headset will work with your cell phone anytime the two units are powered on and in working proximately to each other.

5. Resetting the Headset

When paring the headset to a new Bluetooth TM device, you may want to reset the headset to its default settings. This clears all current parings.

To rest the headset:

1. With the headset turned off, depress and hold down the multi-function control for 12 seconds. The LED will      flash green for approxmately2-3 seconds, then red and green for approximately 7-8 seconds, then orange.      Release the button.
2. The headset will power off automatically after a few seconds the headset has now been reset.

6. General Operation

To Turn the Headset On:
- Press and hold down the multi-function control for approximately 2 second or until you hear a series of short    tones (low tones   followed by high tones)

To Turn the Headset Off:
- Press and hold down the multi-function control for approximately 4 seconds or until you hear a second series of    short tones (this time, high tones followed by low tones).

Adjusting the Volume
- You can adjust the headset listing volume during a call by rocking the multi-function controller wheel forward    twice for each volume level increases you desire.
- To decrease the volume, rock the multi-function controller wheel backwards twice for each volume level     decrease you desire. There are eight separate (8) volume levels.

- Note be sure to merely rock the multi-function controller wheel forward or backward during adjustments. Do not press down, as you will end your call.

Making and Receiving Calls
Once you have paired the STEP 1150 with you phone, you can make and receive calls using the headset as long as it is turned on and within range of the phone (up to 0m./30 ft).

Note: the multi-function Led indicator flashes green more rapidly during a call or active transmission of information (e.g. dialing) to indicate it is communicating with your phone.

For phones without voice-dialing capability, once you headset is paired to your phone, dial the number as you normally would using the keypad on your phone and use the headset to converse with your party. For voice-dialing, please refer to their section that follows.

When using the headset to receive a call, press down the multi-function control briefly once to answer a call. To end a call, press down the multi-function control briefly a second time.

Voice Dialing
If your phonies equipped with a voice-dialing mode, you can place calls with your voice commands. To make a call using voice dialing

1. Make sire the phone and the headset is on and within range of each other. Press down the multifunction      control  once.
2. After the beep, voice dial as you normally would.
3. End the call by pressing down the multi-function control on your headset. You can also end a call by pressing      the END or NO key on your phone.

Please refer to your phone’s user manual or documentation for more information on voice dialing and control.

Answering Calls
To answer a call using the headset

1. When the phone rings or when you hear your phone ring through the headset, briefly press down the multi-      function control once.

2. End the call by pressing down the multi-function control on your headset, or the END or NO key on your phone.     Answering a second call (if you phone supports multiple incoming calls) You must use the phone keypad to     answer and handle a second  call, but you can still use the headset for talking  and listening. You cannot use     the multi-function control to answer the second call. Refer to your phone’s user manual or documentation for     details on how handle more than one call simultaneously.